5 GAL KIT TERRAZZO EPOXY
CLEARLIGHT GRAYDARK GRAYBLACKTANBEIGESAFETY GREEN - $20.00MEDIUM GRAYSAFETY BLUE - $20.00MOCHASAFETY YELLOW - $20.00TILE RED - $20.00WHITE
The uniqueness and universality of E2U Epoxy’s chemistry facilitates the applications where USDA Food & Beverage and other regulatory requirements must be obtained. i.e. food manufacturing and preparation, pharmaceutical manufacturing and dispensaries, clean rooms, commercial kitchens, laboratories and more. Other areas of use include: garage floors, rest rooms, manufacturing facilities, automotive showrooms and schools.
Self-priming over properly prepared substrate
High color stability
Withstands medium traffic as thin as 12 mil
No amine blush
Before coating is applied, concrete must be:
Dry – No wet areas
Clean – Contaminants removed
Profiled – Surface etched
Sound – All cracks and spalled areas repaired
Note: Mechanical preparation is the preferred method of preparing concrete for coating application. Shot-blasting, diamond grinding, scarifying and scab- bling are all acceptable methods.
Voids, cracks and imperfections will be seen in finished coating if the concrete is not patched correctly. Patch concrete with E2U Patch. After the patching mate- rial is cured, diamond grind patch. If another patching material is used, contact a E2U technical representative for a compatible and approved alternative
All surfaces are not the same. It is recommended that a sample area be done before the start of the project. The test should be done on-site, using the pro- posed method by the assigned applicator to insure proper adhesion and color. A sample area should also be done on any existing coatings to determine if any contaminants exist or if delaminating will occur.
E2U Epoxy, while in an un-reacted state, may be cleaned up with hot water and degreaser. Isopropyl alcohol or acetone may be needed once the resin begins hardening. Lastly, a strong solvent like methylene chloride may be required if resin is nearly set up.
The ratio of Top Shelf Epoxy is 2 to 1. That is, two parts A (resin) to one part B (hardener). Mix the following with a drill and mixing paddle. Note: If using a drill mixer, use a low speed (not to exceed 300 rpm) to prevent air entrapment.
Premix 1 gallon of Part A for 30-45 seconds.
Add 1/2 gallon of Part B and mix for another 60-90 seconds.
E2U Epoxy is designed to be immediately poured on the floor. Leaving mixed product in the container will greatly reduce pot life. Once poured out on the floor, 20-30 minutes of working time can generally be expected.
Application of E2U Epoxy for a nominal 20 to 30 mil coating system is applied in two coats and in one pass as a top coat. For estimation purposes, use 200 SF per gallon in either case.
1. Always apply in descending temperatures. Concrete is porous and traps air. In ascending temperatures (generally mornings) the air expands and can cause out gassing in the coating. It is safer to apply coatings in the late afternoon, especially for exterior applications.
2. Optimum ambient temperature should be between 55-90°F during application. Note: Cure times are affected by ambient and slab temperatures. Temperatures of 55°F and lower can slow cure times. Temperatures of 85°F and higher will speed up working and times.
3. Mix three gallons of resin using above mixing instructions.
4. Apply approximately 200 SF per gallon (150 SF per gallon for a top coat over Industrial Quartz systems) by immediately pouring out on surface in a ribbon, while walking and pouring at the same time until bucket is empty.
5. Using a squeegee on a pole, pull E2U Epoxy over substrate. As a first coat over bare concrete, pull resin as thin as possible while still wetting out concrete and uniformly covering surface. This allows trapped air to escape more easily. To apply in a single coat over an Industrial Epoxy system, pull at about 200 SF per gallon.
6. Using a 3/8” non-shedding phenolic (plastic) core paint roller, roll coating for- wards and backwards.
7. Lastly, back roll in the opposite direction as step 6.
8. Apply second coat by repeating steps 1-7 the within 12 hours. Failure to recoat during this window may result in fish eyes. Always sand floor after 12 hours before recoat.
CHIP/SILICA SAND BROADCAST INSTRUCTIONS
1. Following Step 6 above. Broadcast Color Chips/Micro Chips (at 16 lbs. per 100 sq. ft.) by tossing them into the air and allowing them to gently rain down into the wet resin..
2. For a random broadcast, use 1 lb. of chips per 100 sq. ft..
3. Allow to cure. Then scrape the basecoat with a drywall scraper in all directions. Vacuum small pieces and dust.
Silica Sand Broadcast
1. Following Step 6 above, gently throw the silica sand up into the air, allowing it to fall without lumping in one spot or moving the resin. Do this until the floor is totally saturated with the silica sand and the resin will not accept any more. This generally requires 1/2 to 3/4 lbs. per sq. ft.. Allow to dry for 6-8 hours.
4. Sweep floor and stone any high spots.
5. Following either method, apply seal coat of E2U Epoxy/Polyaspartic 100 at approx. 150 sq. ft. per gallon.
DATASHEET & SDS
Terrazo Epoxy Datasheet
Terrazo Epoxy SDS - A Side
Terrazo Epoxy SDS - B Side
GALLERY & TRAINING VIDEO
Toll-Free: (855) EPOXY2U(855) 376-9928
Call: (714) 477-8700
The world premium floor coating made by Epoxy2U in the USA. We operate a 20,000 square foot manufacturing facility in Fullerton, CA.